A heated footwear order usually reaches the factory with a style, a battery specification and a size range. What rarely arrives is an agreed size curve — the distribution of units across those sizes that tells the factory how many pairs to cut in each one. That gap is where most sizing disputes begin: the brand's design team reads one set of numbers, the buyer's planning sheet reads another, and the supplier builds to a third.
As a Shenzhen EVA foam products manufacturer handling OEM and private-label orders, we see the same argument return every winter season. Here is how we close it with customers before tooling, sampling or bulk cutting starts.
The disagreement is seldom about whether a size range exists. It is about what each number in that range stands for.
Our rechargeable heated winter boots page gives one size range in the specification block, while the page summary for the same product carries a different figure for that field. A related snow-boot listing on our site shows two ranges attached to two colourways rather than one shared range. We raise this with every buyer who quotes from a screenshot.
None of those figures is a specification to build to. The point is not that the pages are wrong; it is that published size numbers on any supplier's site — ours included — are listing values, not manufacturing values. A production range has to be confirmed in writing against the approved sample, with the last, the lining stack and the battery position all fixed.
Our washable rechargeable heated insoles work differently again. Because they are trimmed to fit, a single blank covers a broad span of label sizes, so the assortment question becomes how many blanks per carton rather than how many pairs per size. Read as a footwear curve, that item is over-ordered in the middle sizes and short at both ends.
The remedy is procedural rather than technical. Five confirmations settle nearly every case we have handled.
| Item to confirm | Why it settles the disagreement |
|---|---|
| One size system for the whole order | Choose EU, US or UK as the controlling label and state the conversion you expect on the hangtag. Lasts, insoles, cartons and labels all follow that decision. |
| Size range per colourway, not per style | Where a style is sold into different markets or with different uppers, the available sizes often differ by colour. Confirming this per colour avoids an order that cannot be filled. |
| The curve as unit counts | Ask for units per size across the total order quantity instead of a percentage band. Whole numbers leave no room for interpretation and can be checked against the packing list. |
| Fit sign-off on the production sample | Fit comments made on an early sample with different lining or wiring do not carry over. Sign-off should happen on the sample built in the production configuration. |
| Written confirmation of every published figure | Any size number taken from a catalogue, listing or image stays unconfirmed until it appears in the signed specification sheet. |
Our custom cooperation process runs from needs consultation through proposal and quotation, design drafts and renderings, mould opening and print moulding, signature confirmation, and a 30% deposit on signing. The size curve belongs at the quotation stage: once moulds are open, a changed curve also changes cutting dies, pack-out and carton counts.
For retail and cross-border buyers the size curve is also a working-capital decision. A curve copied from a competitor's listing tends to leave dead stock in the middle sizes and gaps at the extremes — the two failure modes that surface as markdowns in the same season. Two habits reduce that risk:
Our non-slip and heated footwear range covers slippers, insoles and winter boots, each with its own sizing logic. Treating them as one family in the assortment plan is the quickest route to the mismatch described here.
Work with an OEM and ODM EVA foam manufacturer that reads your curve the same way you do
Shenzhen Fulikai Packaging Products Co., Ltd. has produced custom EVA foam products for overseas brands, gift companies and cross-border sellers since 2008. Our Shenzhen factory runs foaming, cutting, stamping and laser processing in-house, with full manual inspection before shipment and support for third-party inspection and buyer audits.
Call or message +86 13827489472, email sales@fulikaisz.com.cn, or send your size curve through our inquiry page for a specification sheet and quotation.
Tel
+86 13827489472
+86 13827489472
sales@fulikaisz.com.cn
5th Floor, Building B, Yuanfen Industrial Zone, Dalang Street, Longhua District, Shenzhen, China