Welcome to the official website of Shenzhen Fulikai Packaging Products Co., Ltd.

Shenzhen Fulikai Packaging Products Co., Ltd.

With 19-year experience in manufacturing & customizing EVA foam products.Certified by Coca-Cola, Walmart & Sedex, supporting factory audits.

Custom Service Hotline+86 13827489472+86 0755-29018797

Fulikai - Fast production and delivery within 15 days
Your position: Home > Blog

What Should Inspectors Check About color separation and count accuracy in a Bulk Order of foam dice and counting cubes?

Back to list Release Date: 11/16/2026

A container of foam dice and counting cubes looks simple: small cubes of EVA foam, printed pips, a few colours. That simplicity is exactly why bulk orders go wrong quietly. One shade drift in a mixed set, one short carton in a multi-piece pack, and the complaint lands on your warehouse, not on the factory floor. This guide sets out what an inspector — yours, ours, or a third party's — should actually check at each stage of a bulk order for these two SKUs.

Scope of this article: 20 mm six-sided EVA foam dice with printed pips and solid-colour EVA counting cubes, ordered in bulk packs under an OEM or wholesale purchase order. Pack size and colour ratio are set by your artwork and purchase order, so the numbers below are the ones you define and we confirm before production.

Why these two SKUs are inspected differently from moulded plastic dice

Injection-moulded plastic dice fail at the mould, so a bad batch fails as one consistent unit. Foam dice and counting cubes are made from sheet and block EVA that is foamed, coloured, cut, printed and packed in separate steps. Each step adds its own variation:

  • Colour comes from the foam, not a paint layer. At our factory the colour is formed in one-step foaming with added colour masterbatch, so a batch change shows up as a tone shift across the whole cube rather than a surface patch.
  • Pips are printed after cutting — by heat-transfer or silk-screen printing — so pip position, coverage and adhesion are process variables, not mould constants.
  • Dimensions come from cutting. Stamping and laser cutting set the edge geometry, which means cube size and squareness can drift within a run and between runs.
  • Counts are assembled by hand into packs, which is where short counts and mixed-colour ratios usually appear.

An inspection plan for these products therefore has to cover colour, print, dimension and count as four separate checks with their own sampling rules, not one generic "does it look right" pass.

Before production: lock the references an inspector can measure against

Most disputes on colour and count start because the purchase order describes the product in words. Before tooling or plate-making, agree on written references:

  • A signed physical pre-production sample. Keep one approved dice set and one approved cube set per colour as the golden sample; both factory and inspector hold a copy.
  • A colour reference for every colour in the mix. State the masterbatch colour standard, not just "red" or "green". Where your artwork names a Pantone or RAL code, put it on the drawing.
  • Tolerance on edge length and pip placement written as numbers, for example the acceptable range around 20 mm and the maximum offset of the pip pattern from the face centre.
  • A stated count per pack and colour ratio per pack, agreed on the purchase order — for example a fixed number of pieces with an equal split across the colours in the mix.
  • Pack contents list: box, insert, storage bag (counting cubes ship with a non-woven drawstring bag), barcode position.

An inspector can only report against something written. If the tolerance is not on the drawing, "close enough" becomes the standard — and it will be argued about after the goods arrive.

Colour separation: what to check and how

In this product family, colour separation covers two different risks. The first is cross-contamination between colours in a mixed pack: cubes of the wrong shade or the wrong colour sitting inside a sorted set. The second is print bleeding through from one side of a die to another, where ink migrates over an edge and dirties an adjacent face.

1. Shade consistency within one colour

Take the sample carton at random, pull ten pieces of the same colour from different cartons in the pallet, and lay them side by side in daylight or a standard light booth. Because the pigment is inside the foam, a shift reads as a visible difference in saturation across the group. Compare against the golden sample, not against a photo on a screen.

2. Colour mix ratio in a multi-colour pack

Open a defined number of packs and count pieces by colour. If the purchase order specifies an equal split across the colours in the mix, then 46 of one colour and 54 of another is a packing-line error, not a moulding one, and it repeats across the pallet if nobody checks it. Record the actual counts, not an impression.

3. Colour bleed and pip-edge contamination

Inspect each face of the dice under raking light. Look for ink that has travelled past the edge onto the neighbouring face, ghosting around the pip pattern, and pale patches where the print did not transfer fully. Heat-transfer printing with a white base is designed to stop the underlying foam colour showing through the print; when the base pass is skipped or thin, the printed pips look washed out on darker foams.

4. Print adhesion

Rub a pip with a firm thumb, then repeat with a white cloth dampened with water and, if your market requires it, with saliva-simulant solution for children's products. Ink that lifts onto the cloth fails regardless of how good the print looked at first sight. This is also the check that catches an ink batch that does not meet the environmental test the order calls for.

Count accuracy: where short counts actually come from

Counting every piece in every pack is not practical in the time an inspector has. What works is a defined sampling plan plus a weight check:

  • Weigh-by-count. Weigh a verified group of pieces, calculate the average unit weight, then weigh full packs and convert back to a count. A pack that reads three pieces short is found in seconds. Record the unit weight on the report so the calculation can be audited.
  • Open-carton count. Open a sample of cartons across the pallet — top, middle and bottom layers — and do a full manual count on at least one carton per layer.
  • Pack-count reconciliation. Compare the total number of packed sets against the packing list and the carton-marking tally. A mismatch between sets produced and cartons shipped is usually found here, not in the open-carton count.
  • Colour ratio per pack, as described above, counted rather than estimated.

Ask the factory to run its own full manual inspection before the inspector arrives. We carry out complete manual inspection of every unit before shipment and reject defective items at that stage, so the third-party visit confirms a process instead of rescuing an uncontrolled one.

The physical checks that go with colour and count

CheckHow to perform itWhat a fail looks like
Edge length and squarenessMeasure ten pieces per colour with calipers against the drawing tolerance.Cubes that vary enough to look uneven on a table, or dice that rock when placed flat.
Corners and edgesRun a finger along every edge of a sample group; look for burrs, tears and hard corners.Rough or sharp edges on a product sold to young children.
Density and reboundSqueeze a piece firmly and release; drop a sample from table height.Cubes that stay compressed, feel dense and heavy, or bounce inconsistently within one colour.
Pip print clarityRead the pip pattern at arm's length on ten pieces per colour.Missing pips, doubled pips, or patterns sitting off-centre on the face.
Smell and surface residueOpen a sealed carton and note odour; wipe a piece with a dry white cloth.Strong solvent smell on an indoor classroom product, or residue transferring to the cloth.
Cleaning and reuseWipe a printed face repeatedly with a damp cloth.Pips fading after a few wipes on a product marketed as washable.
Packaging and labellingCheck box artwork, insert, warning text, age grading and barcode against the approved file.Old artwork version, missing small-parts or suffocation warning, wrong item code.

Safety checks that belong in the same visit

A 20 mm cube is close to a choking-hazard dimension, so the age grading on the pack and the safety testing behind it are part of the inspection, not a separate conversation. Confirm that the product's children's-toy safety test report covers the exact material and ink batch in the shipment, and that the packaging carries the warnings your market requires. Our production run includes sixteen types of test — colour fastness, tensile strength, ink environmental testing and children's-product safety testing among them — carried out during production rather than only at the end.

If your buyer or brand owner has an audit protocol, tell us before the order is placed. Our published pages reference Coca-Cola, Walmart and Sedex audit reports; we support 100% third-party inspection and welcome audits conducted by the customer's own team. Ask for the specific report you need before the order is placed.

Where in the schedule each check belongs

StageWhat to verify
Sample approval (typically 5–7 working days for custom artwork)Colour against your artwork, pip layout, edge length, pack format. Sign and date the golden sample; keep a copy at both ends.
In-line / during productionShade consistency between foam batches, print adhesion on fresh prints, count rate on the packing line. Catching a tone shift here saves the whole run.
Pre-shipment (most cartons packed and sealed)Weight-based count, open-carton count, colour ratio, physical and safety checks above, carton drop and stack check.
LoadingCarton count against the packing list, outer-carton markings, seal numbers.

What to put in the acceptance criteria before you order

  • Colour: no visible difference from the golden sample under agreed lighting; state the maximum acceptable deviation if your brand uses a numeric colour tolerance.
  • Count: exact count per pack as specified, with zero tolerance on short packs at retail level; state the sampling plan and acceptance limits for the pre-shipment visit.
  • Print: 100% of pips legible and correctly positioned within the stated offset; no bleed past edges; adhesion pass on wet-rub test.
  • Physical: dimensions inside the drawing tolerance; no sharp or torn edges on any sampled piece.
  • Safety: valid test report for the shipped material and ink, correct warnings and age grading on pack.

How we work with your inspector

Fulikai manufactures both products as standard EVA educational toys: the dice in a six-sided format with printed pips, supplied in mixed colours and in a bulk pack; the counting cubes as solid, uniform-size cubes with a drawstring storage bag. Edge length, colour set, print and packing are customised to your drawing under an OEM order, and both run through our own foaming, cutting, stamping and laser lines.

On timing: plate-making for custom artwork takes 5–7 days, and bulk orders can be delivered within 15 days once the order is confirmed. The cooperation process runs from requirements consultation, proposal and quotation, design drafts and renderings, mould opening and print moulding, sign-off, then a 30% deposit on contract signature.

Send us your artwork, target pack size and destination country. We will recommend raw materials that meet the standards for your market and quote against your drawing — including the inspection points above written into the order.

Phone: +86 13827489472  ·  Email: sales@fulikaisz.com.cn  ·  Send an inquiry  ·  Custom capabilities

News center

Tel

+86 13827489472
  • Tel

    +86 13827489472

  • E-mail

    sales@fulikaisz.com.cn

  • Add

    5th Floor, Building B, Yuanfen Industrial Zone, Dalang Street, Longhua District, Shenzhen, China

Copyright © Shenzhen Fulikai Packaging Products Co., Ltd. Main business: Puzzle mat, EVA nail file, EVA educational toy, EVA slippers, EVA foam.
Blog